Makita Drill Drivers

Makita 6337DWDE3 14.4v Drill Driver

Makita 6337Dwde3 14.4v Cordless Drill Driver

Features:
- Two Mechanical Gears
- Forward /Reverse Rotation
- Variable Speed Trigger

Specifications:
Capacity Max: Steel - 13mm
Capacity Max: Wood - 32mm
Torque Settings: S /H Nm 16; 30 /65
No Load Speed: Hi 0-1300rpm, Lo 0-400rpm
Net Weight: 2.1Kg
Battery: 14.4v 2.6Ah NiMh
Charging Time: 1 Hour

What Drill For You?

Superb examples of 12v Cordless Drill Drivers include the Black & Decker CD12CA 12v, Bosch PSR 12v, DeWalt DW907K2V 12v, Hitachi 12DVF3 12v, Makita 6270DWPE3 12v, and also the Ryobi CHD1202 12v

In Case 14.4v Cordless Drill Drivers are more your thing, then be sure to look at the Black & Decker CP142KB 14.4v Drill Driver, Bosch PSR 14.4v Drill Driver, DeWalt DC731KA 14.4v Drill Driver, the Hitachi DSDL Li-Ion 14.4v Drill Driver,Makita BHP442z 14.4v Drill Driver, or the Ryobi CCD-1441 14.4v Drill Driver

For all your your 18v Cordless Drill Drivers requirements, go ahead and review the Black & Decker CD18CA 18v, Bosch PSR18VE-2 18v Drill Driver, DeWalt DC920KB 18v Drill Driver, Hitachi DS18DFL 18v Drill Driver, the Makita 6390DWPE3 18v Drill Driver or the Ryobi CCD-181M One+ 18v Drill Driver

Your DIY Safety First

The most significant positive of the cordless drill driver over its powered partner is the freedom to be utilized anywhere, the downside of a battery drill is the harder you work the drill the speedier the battery runs out, so you have to make sure that you are buying the right voltage cordless drill driver for the job, there is no point in investing money into a 12 volt drill and expecting it to be able to drill fifty 16mm holes from one set of batteries because it won’t.

The Drills come in two standard sizes and they are SDS Plus (10mm) and SDS-Max (18mm). These sizes relate the size of the shank. SDS Plus is the many common and can withstand a hammer of up to 4Kg, and SDS Max for hammers over 5Kg. SDS Plus grips the drill bit in two places whereas SDS Max grip in three places. With the SDS drill you can use a chuck adaptor that when utilized enables the use of standard drill bits for rotary drilling. It is wise to avoid SDS Drills that do not have a safety clutch. If the drill bit jams and is unable to turn a safety clutch may stop the drill body from spinning. This spinning may cause severe damage to the wrist and arm with the possibility of the drill being yanked from your hand, jumping out of the hole and coming into contact with a part of the body. A safety clutch could be high on your list of required features.

The least expensive drill drivers run at a single speed, but many have two fixed speeds: 300 rpm and 800 rpm. A slide switch or trigger lets you select high or low speed. These drill drivers are ideal for many light-duty operations. The low speed is for driving screws, the high speed for drilling holes. For more refined carpentry and repair tasks, chose a drill that has the same two-speed switch and a trigger with variable speed control that lets you vary the speed from 0 rpm to the top of each range. And if you do more hole drilling than screwdriving, look for more speed, 1000 rpm or higher at the top end.

Accessories for drill drivers include bits for drilling wood, metal, ceramic, glass, and masonry. In addition to bits other accessories include hole saws, screwdriver bits, files, rasps, and sanders.

Nickel-metal-hydride (NiMH) batteries represent the latest breakthrough in batteries. They're smaller and run longer than standard nickel-cadmium (Nicad) batteries. NiMH batteries also pose less of a hazard when it comes to disposal than Nicads because they don't contain any cadmium, which is highly toxic. Makita, Bosch, Hitachi and DeWalt offer NiMH batteries, and other manufacturers may soon produce these power cells too.

Check out drill drivers in DIY centres noting their weight and balance. Try out vertical and horizontal drilling positions to see how comfortable you feel. Contoured grips and rubber cushioning on some models make them very comfortable, even when you're applying direct palm pressure. While you're at it, see how easy it is to change clutch settings and operate the keyless chuck.

When drilling deep or large holes, it is best to drill a small pilot hole first. This is very helpful when drilling deep holes because it's sometimes easier to keep the hole straight with a smaller bit. A larger bit may then normally follow the pilot hole. When drilling larger holes, especially in metal, the pilot hole opens an area in the metal to accommodate the tip of the larger bit so the cutting surfaces may more easily reach the uncut metal. Once you've drilled your hole, you'll probably find a burr on the back surface of your material. This may be removed by lightly drilling the back side of the hole with a larger bit. If the material is thin, such as sheet metal, instead of a burr you may find the material is actually distorted leaving a ragged hole. This be prevented by sandwiching the material between two pieces of wood before you drill the hole. As with all tools, exercise caution, wear safety equipment and learn to use the tools properly.

Not all holes need to go all the way through the material. Some holes need only be a certain depth in the wood. The easiest way to make certain you drill the correct depth is to measure the necessary hole depth on your drill bit. Then mark that point on the bit with a marker or wrap some tape around the bit at the measured spot. Then when you drill only insert the drill bit to the mark or tape. You may also purchase bit collars that slide over the bit and are secured at the appropriate depth. The collars usually attach with a small hex wrench or screwdriver. The drilling is undertaken and you have to get the bit out. Give the drill a little power to spin the bit and slowly pull it out of the hole. Don’t be too speedy or pull it out without spinning the bit. Either of these may cause the bit to bind in the hole. The hole is complete and now you need to attach the fastener. Bits can be inserted into the drill turning the drill into a screwdriver or wrench. If you are attaching screws determine the size of the screw head and select a matching screwdriver bit. Connect the screwdriver bit to the drill in the same way you would other bits. Put the bit head in the screw head and squeeze the trigger. Be careful not to provide so much power that you go all the way through the material (if that’s not called for) or pressure the screw head too far down into the material. It’s easy to get carried away with the power of the drill. If you are attaching a bolt fastener you may also purchase bolt sockets that may be attached to the drill. Match the bit size with the bolt, attach the bit to the drill, and screw in the bolt.

Learning how to sharpen drill bits is cost effective, it better to keep a bit sharp by occasional sharpening rather than waiting until it becomes really blunt. A sharp bit cuts better with less effort whether utilized in a power or hand drill. A sharp bit may also give a cleaner hole.

DIY Safety tips:

Always unplug an appliance before working on it and always use the correct fuse for the circuit or appliance. Fitting a fuse of incorrect rating is dangerous. As an additional precaution, wear rubber soled shoes. This may provide a measure of insulation between you and the ground.
When painting, or using any material that generates toxic fumes or dust, keep the room well ventilated. Never smoke while painting or standing close to a freshly painted area.

Don't wait until disaster strikes to find your stop-cocks and gate valves. Opening and closing them four times a year may ensure they easily work when you need them to. Don't let a blown fuse leave you in the dark: keep a repair kit nearby your mains fuse box, with a torch - check the batteries regularly - screwdrivers, spare fuses, bulbs and fuse wire, rubber gloves and insulated pliers, a trimming knife and insulating tape.

Take extra care with old paint. Some old paint could give off harmful dust and pose a poisoning hazard if ingested by small children. You must not burn off old paint or rub it down with dry sandpaper or a power sander; you could clean up properly, using a high efficiency industrial vacuum cleaner with heavy duty filters. Have a basic First Aid kit accessible.

If you have any doubts whatsoever about how to safely use any material, or equipment, ask the manufacturer or supplier.